how to remove rig gear in kitchenaid stand mixer ?

Removing the Rig Gear from a KitchenAid Stand Mixer

Removing the rig gear from a KitchenAid stand mixer is a relatively simple process that can be completed in a few steps. The rig gear is a component of the mixer that helps to maintain the mixer’s speed. It is important to replace the rig gear if it becomes worn out, as this could cause the mixer to slow down or stop working altogether. Here are the steps to successfully remove the rig gear from your KitchenAid stand mixer.

Step 1: Unplug the mixer and remove the bowl.

The first step to removing the rig gear is to make sure the stand mixer is unplugged and the bowl is removed. This will make it much easier to access the components of the mixer.

Step 2: Remove the screw and washer.

Once the bowl is removed, you will need to locate the screw and washer that hold the rig gear in place. These can usually be found on the bottom of the mixer near the base. Use a Philips head screwdriver to remove the screw and washer.

Step 3: Loosen the gear.

Once the screw and washer are removed, you will need to loosen the gear. You can do this by using a small wrench or pliers to grip the gear and turn it counterclockwise until it loosens.

Step 4: Pull out the gear.

Once the gear is loosened, you can pull it out from the mixer. Be sure to hold onto the gear so it doesn’t fall out while you are removing it.

Step 5: Install the new gear.

Once you have removed the old gear, you can install the new gear. Place the gear in the slot and make sure it is aligned correctly. Then use the screw and washer to secure the gear in place.

Removing the rig gear from a KitchenAid stand mixer is a relatively simple process that only takes a few steps. Just make sure the mixer is unplugged before you begin and be sure to follow the steps outlined above. Once the new gear is installed, your KitchenAid mixer will be back to working like new.

Frequently Asked Questions

FAQ 1: How do I remove the Rig Gear from my KitchenAid Stand Mixer?
Answer: To remove the Rig Gear from your KitchenAid Stand Mixer, start by unplugging the mixer from the power source. Then, use a Phillips-head screwdriver to loosen and remove the two screws from the bottom of the mixer. Next, use a flat-head screwdriver to gently pry around the edges of the gear cover to loosen it and lift it off. Finally, use a pair of needle-nose pliers to carefully remove the Rig Gear from the mixer.

FAQ 2: What is the Rig Gear used for in a KitchenAid Stand Mixer?
Answer: The Rig Gear in a KitchenAid Stand Mixer is used to power the beater and the agitator. The Rig Gear is connected to the beater shaft, and when the mixer is in operation, it rotates the beater shaft and powers the beater and agitator.

FAQ 3: How do I replace the Rig Gear in my KitchenAid Stand Mixer?
Answer: To replace the Rig Gear in your KitchenAid Stand Mixer, start by unplugging the mixer from the power source. Then, use a Phillips-head screwdriver to loosen and remove the two screws from the bottom of the mixer. Next, use a flat-head screwdriver to gently pry around the edges of the gear cover to loosen it and lift it off. Finally, use a pair of needle-nose pliers to carefully remove the old Rig Gear and replace it with the new one.

FAQ 4: How often should I replace the Rig Gear in my KitchenAid Stand Mixer?
Answer: The Rig Gear in your KitchenAid Stand Mixer should be replaced every two to three years, or when it starts to make a grinding sound when the mixer is in operation.

FAQ 5: What type of screwdriver do I need to remove the Rig Gear from my KitchenAid Stand Mixer?
Answer: To remove the Rig Gear from your KitchenAid Stand Mixer, you will need to use a Phillips-head screwdriver to loosen and remove the two screws from the bottom of the mixer, and a flat-head screwdriver to gently pry around the edges of the gear cover to loosen it and lift it off.

Similar Posts

Leave a Reply

Your email address will not be published.